Ubuntu下安裝xl2tpd服務(wù)

2024-06-28 16:04:46

字體：大中小

供稿：網(wǎng)友

apt-get install openswan xl2tpd ppp lsofiptables -t nat -A POSTROUTING -j SNAT --to-source <IP地址> -o eth0echo "net.ipv4.ip_forward = 1" | tee -a /etc/sysctl.confecho "net.ipv4.conf.all.accept_redirects = 0" | tee -a /etc/sysctl.confecho "net.ipv4.conf.all.send_redirects = 0" | tee -a /etc/sysctl.confecho "net.ipv4.conf.default.rp_filter = 0" | tee -a /etc/sysctl.confecho "net.ipv4.conf.default.accept_source_route = 0" | tee -a /etc/sysctl.confecho "net.ipv4.conf.default.send_redirects = 0" | tee -a /etc/sysctl.confecho "net.ipv4.icmp_ignore_bogus_error_responses = 1" | tee -a /etc/sysctl.conffor vpn in /PRoc/sys/net/ipv4/conf/*; do echo 0 > $vpn/accept_redirects; echo 0 > $vpn/send_redirects; donesysctl -p

編輯/etc/ipsec.conf

version 2 # conforms to second version of ipsec.conf specificationconfig setup dumpdir=/var/run/pluto/ #in what directory should things started by setup (notably the Pluto daemon) be allowed to dump core? nat_traversal=yes #whether to accept/offer to support NAT (NAPT, also known as "IP Masqurade") workaround for IPsec virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v6:fd00::/8,%v6:fe80::/10 #contains the networks that are allowed as subnet= for the remote client. In other Words, the address ranges that may live behind a NAT router through which a client connects. protostack=netkey #decide which protocol stack is going to be used. force_keepalive=yes keep_alive=60 # Send a keep-alive packet every 60 seconds.conn L2TP-PSK-noNAT authby=secret #shared secret. Use rsasig for certificates. pfs=no #Disable pfs auto=add #the ipsec tunnel should be started and routes created when the ipsec daemon itself starts. keyingtries=3 #Only negotiate a conn. 3 times. ikelifetime=8h keylife=1h ike=aes256-sha1,aes128-sha1,3des-sha1 phase2alg=aes256-sha1,aes128-sha1,3des-sha1 # https://lists.openswan.org/pipermail/users/2014-April/022947.html # specifies the phase 1 encryption scheme, the hashing algorithm, and the diffie-hellman group. The modp1024 is for Diffie-Hellman 2. Why 'modp' instead of dh? DH2 is a 1028 bit encryption algorithm that modulo's a prime number, e.g. modp1028. See RFC 5114 for details or the wiki page on diffie hellmann, if interested. type=transport #because we use l2tp as tunnel protocol left=服務(wù)器IP地址 #fill in server IP above leftprotoport=17/1701 right=%any rightprotoport=17/%any dpddelay=10 # Dead Peer Dectection (RFC 3706) keepalives delay dpdtimeout=20 # length of time (in seconds) we will idle without hearing either an R_U_THERE poll from our peer, or an R_U_THERE_ACK reply. dpdaction=clear # When a DPD enabled peer is declared dead, what action should be taken. clear means the eroute and SA with both be cleared.

編輯 /etc/ipsec.secrets 添加一行

IP地址 %any: PSK "secure_password"

編輯/etc/xl2tpd/xl2tpd.conf

[global]ipsec saref = yessaref refinfo = 30;debug avp = yes;debug network = yes;debug state = yes;debug tunnel = yes[lns default]ip range = 172.16.1.30-172.16.1.100local ip = 172.16.1.1refuse pap = yesrequire authentication = yes;ppp debug = yespppoptfile = /etc/ppp/options.xl2tpdlength bit = yes

編輯/etc/ppp/options.xl2tpd

require-mschap-v2ms-dns 8.8.8.8ms-dns 8.8.4.4authmtu 1200mru 1000crtsctshide-passwordmodemname l2tpdproxyarplcp-echo-interval 30lcp-echo-failure 4

編輯/etc/ppp/chap-secrets

Secrets for authentication using CHAP# client server secret IP addressesbob l2tpd DF98F09F74C06A2F *service ipsec restartservice xl2tpd restart

上一篇：阿里云ECS(ubuntu16.04)安裝mysql遇到的一些問題

下一篇：ubuntu 14.04 LTS 系統(tǒng)安裝