Cisco交換機綜合配置實例(一)

2019-11-05 01:57:06

字體：大中小

來源：轉載

供稿：網友

　　本實例綜合性很強,基本上包含了Cisco交換機的所有交換技術

1.　網絡拓撲和相應設計

目錄:

網絡配置實例

網絡拓撲和相應設計

Catalyst 5509 配置

Catalyst 4003　配置

RSM　配置

Catalyst 5505　配置

網絡拓撲和相關設計

網絡拓撲圖

　 Cisco交換機綜合配置實例(一)（圖一）

2.　Catalyst 5509 的配置

下面列出 Catalyst 5509 的基本配置

Enter passWord:

Console> enable

Enter password:

Console> (enable) set system name 5509-ER-F1

System name set.

5509-ER-F1> (enable) set system location 1st Floor Equipment Room

System location set.

5509-ER-F1> (enable) set system contact sysadmin@bigcorp.com

System contact set.

5509-ER-F1> (enable) set time 04/30/1999 9:30:00

Fri APR 30 1999, 09:30:00

5509-ER-F1> (enable) set password

Enter old password:

Enter new password:

Retype new password:

Password changed.

5509-ER-F1> (enable) set enablepass

Enter old password:

Enter new password:

Retype new password:

Password changed.

5509-ER-F1> (enable) set banner motd %

5509-ER-F1 (Catalyst 5509)

access Restricted

%

MOTD banner set

5509-ER-F1> (enable) set interface sc0 10.10.1.10/24

Interface sc0 IP address set.

5509-ER-F1> (enable) set ip route default 10.10.1.1

Route added.

5509-ER-F1> (enable) set ip dns server 10.10.10.100

10.10.10.100 added to DNS server table as primary server.

5509-ER-F1> (enable) set ip dns domain bigcorp.com

Default DNS domain name set to bigcorp.com

5509-ER-F1> (enable) set ip dns enable

DNS is enabled

5509-ER-F1> (enable) set vtp domain BigCorp mode server

VTP domain BigCorp modified

5509-ER-F1> (enable) set vlan 10 name Corporate

Vlan 10 configuration sUCcessful

5509-ER-F1> (enable) set vlan 20 name DevEng

Vlan 20 configuration successful

5509-ER-F1> (enable) set vlan 30 name Mfg

Vlan 30 configuration successful

5509-ER-F1> (enable) set vlan 40 name QA

Vlan 40 configuration successful

5509-ER-F1> (enable) set vlan 50 name Finance&Admin

Vlan 50 configuration successful

5509-ER-F1> (enable) set vlan 60 name Sales&Mktg

Vlan 60 configuration successful

5509-ER-F1> (enable) set module name 1 Supervisor III

Module name set.

5509-ER-F1> (enable) set port flowcontrol 1/1-2 send off

Ports 1/1-2 flow control send administration status set to off

(ports will not send flowcontrol to far end)

5509-ER-F1> (enable) set port flowcontrol 1/1-2 receive off

Ports 1/1-2 flow control receive administration status set to off

(ports will not allow far end to send flowcontrol)

5509-ER-F1> (enable) set port negotiation 1/1-2 enable

Ports 1/1-2 negotiation enabled

5509-ER-F1> (enable) set port name 1/1-2 GEC 802.1Q Trunk

Ports 1/1-2 name set.

5509-ER-F1> (enable) set port channel 1/1-2 desirable

Port(s) 1/1-2 channel mode set to desirable.

5509-ER-F1> (enable) set trunk 1/1 desirable dot1q

Port(s) 1/1 trunk mode set to desirable.

Port(s) 1/1 trunk type set to dot1q.

5509-ER-F1> (enable) set module name 3 RSM (RSM-ER-F1)

Module name set.

5509-ER-F1> (enable) set module name 5 Fast Ether Uplinks

Module name set.

5509-ER-F1> (enable) set port name 5/1-4 FEC ISL Trunk

Ports 5/1-4 name set.

5509-ER-F1> (enable) set port speed 5/1-4 100

Ports 5/1-4 transmission speed set to 100Mbps.

5509-ER-F1> (enable) set port duplex 5/1-4 full

Ports 5/1-4 set to full-duplex.

5509-ER-F1> (enable) set port flowcontrol 5/1-4 send off

Ports 5/1-4 flow control send administration status set to off

(ports will not send flowcontrol to far end)

5509-ER-F1> (enable) set port flowcontrol 5/1-4 receive off

Ports 5/1-4 flow control receive administration status set to off

(ports will not allow far end to send flowcontrol)

5509-ER-F1> (enable) set port negotiation 5/1-4 enable

Ports 5/1-4 negotiation enabled

5509-ER-F1> (enable) set port channel 5/1-4 desirable

Port(s) 5/1-4 channel mode set to desirable.

5509-ER-F1> (enable) set trunk 5/1 desirable isl

Port(s) 5/1 trunk mode set to desirable.

Port(s) 5/1 trunk type set to isl.

5509-ER-F1> (enable) set module name 6 DevEng 100Mb Hosts

Module name set.

5509-ER-F1> (enable) set port name 6/1 DE Sparc Ultra

Port 6/1 name set.

5509-ER-F1> (enable) set port name 6/2-7 DE Sparc20

Ports 6/2-7 name set.

5509-ER-F1> (enable) set port name 6/8-12 DE NT Workstation

Ports 6/8-12 name set.

5509-ER-F1> (enable) set port speed 6/1-12 100

Ports 6/1-12 transmission speed set to 100Mbps.

5509-ER-F1> (enable) set port duplex 6/1-12 full

Ports 6/1-12 set to full-duplex.

5509-ER-F1> (enable) set port flowcontrol 6/1-12 send desired

Ports 6/1-12 flow control send administration status set to desired

(ports will send flowcontrol to far end if far end supports it)

5509-ER-F1> (enable) set port flowcontrol 6/1-12 receive desired

Ports 6/1-12 flow control receive administration status set to desired

(ports will allow far end to send flowcontrol if far end supports it)

5509-ER-F1> (enable) set port channel 6/1-12 off

Port(s) 6/1-12 channel mode set to off.

5509-ER-F1> (enable) set trunk 6/1-12 off

Port(s) 6/1-12 trunk mode set to off.

5509-ER-F1> (enable) set spantree portfast 6/1-12 enable

Warning: Spantree port fast start should only be enabled on ports connected

to a single host. Connecting hubs, concentrators, switches, bridges, etc. to

a fast start port can cause temporary spanning tree loops. Use with caution.

Spantree ports 6/1-12 fast start enabled.

5509-ER-F1> (enable) set vlan 20 6/1-12

VLAN 20 modified.

VLAN 1 modified.

VLAN　Mod/Ports

---- -----------------------

201/1-2

　5/1-4

　6/1-12

　

5509-ER-F1> (enable) set module name 7 Corp/Mfg 10Mb Hosts

Module name set.

5509-ER-F1> (enable) set port name 7/1-12 Corp Win98 PC

Ports 7/1-12 name set.

5509-ER-F1> (enable) set port name 7/13-48 Mfg Win98 PC

Ports 7/13-48 name set.

5509-ER-F1> (enable) set port duplex 7/1-48 full

Ports 7/1-48 set to full-duplex.

5509-ER-F1> (enable) set spantree portfast 7/1-48 enable

Warning: Spantree port fast start should only be enabled on ports connected

to a single host. Connecting hubs, concentrators, switches, bridges, etc. to

a fast start port can cause temporary spanning tree loops. Use with caution.

Spantree ports 7/1-48 fast start enabled.

5509-ER-F1> (enable) set vlan 10 7/1-12

VLAN 10 modified.

VLAN 1 modified.

VLAN　Mod/Ports

---- -----------------------

101/1-2

　5/1-4

　7/1-12

　

5509-ER-F1> (enable) set vlan 30 7/13-48

VLAN 30 modified.

VLAN 1 modified.

VLAN　Mod/Ports

---- -----------------------

301/1-2

　5/1-4

　7/13-48

　

5509-ER-F1> (enable) set module name 8 DevEng 10Mb Hosts

Module name set.

5509-ER-F1> (enable) set port name 8/1-48 DevEng WinNT PC

Ports 8/1-48 name set.

5509-ER-F1> (enable) set port duplex 8/1-48 full

Ports 8/1-48 set to full-duplex.

5509-ER-F1> (enable) set spantree portfast 8/1-48 enable

Warning: Spantree port fast start should only be enabled on ports connected

to a single host. Connecting hubs, concentrators, switches, bridges, etc. to

a fast start port can cause temporary spanning tree loops. Use with caution.

Spantree ports 8/1-48 fast start enabled.

5509-ER-F1> (enable) set vlan 20 8/1-48

VLAN 20 modified.

VLAN 1 modified.

VLAN　Mod/Ports

---- -----------------------

201/1-2

　5/1-4

　6/1-12

　8/1-48

　

5509-ER-F1> (enable) set module name 9 DevEng 10Mb Hosts

Module name set.

5509-ER-F1> (enable) set port name 9/1-48 DevEng WinNT PC

Ports 9/1-48 name set.

5509-ER-F1> (enable) set port duplex 9/1-48 full

Ports 9/1-48 set to full-duplex.

5509-ER-F1> (enable) set spantree portfast 9/1-48 enable

Warning: Spantree port fast start should only be enabled on ports connected

to a single host. Connecting hubs, concentrators, switches, bridges, etc. to

a fast start port can cause temporary spanning tree loops. Use with caution.

Spantree ports 9/1-48 fast start enabled.

5509-ER-F1> (enable) set vlan 20 9/1-48

VLAN 20 modified.

VLAN 1 modified.

VLAN　Mod/Ports

---- -----------------------

201/1-2

　5/1-4

　6/1-12

　8/1-48

　9/1-48

　

5509-ER-F1> (enable)

上一篇：Cisco交換機以太網經典配置

下一篇：三層交換機不等于路由器