Enter password: Console> (enable) set system name 4003-ER-F1 System name set. 4003-ER-F1> (enable) set system location 1st Floor Equipment Room System location set. 4003-ER-F1> (enable) set system contact sysadmin@bigcorp.com System contact set. 4003-ER-F1> (enable) set time 04/30/1999 9:45:00 Fri APR 30 1999, 09:45:00 4003-ER-F1> (enable) set password Enter old password: Enter new password: Retype new password: Password changed. 4003-ER-F1> (enable) set enablepass Enter old password: Enter new password: Retype new password: Password changed. 4003-ER-F1> (enable) set banner motd % 4003-ER-F1 (Catalyst 4003) access Restricted % MOTD banner set 4003-ER-F1> (enable) set interface sc0 10.10.1.20/24 Interface sc0 IP address set. 4003-ER-F1> (enable) set ip route default 10.10.1.1 Route added. 4003-ER-F1> (enable) set ip dns server 10.10.10.100 10.10.10.100 added to DNS server table as primary server. 4003-ER-F1> (enable) set ip dns domain bigcorp.com Default DNS domain name set to bigcorp.com 4003-ER-F1> (enable) set ip dns enable DNS is enabled 4003-ER-F1> (enable) set vtp domain BigCorp mode client VTP domain BigCorp modified 4003-ER-F1> (enable) set module name 1 Supervisor Module name set. 4003-ER-F1> (enable) set module name 2 Gig Uplinks Module name set. 4003-ER-F1> (enable) set port flowcontrol 2/1-2 send off Ports 2/1-2 flow control send administration status set to off (ports will not send flowcontrol to far end) 4003-ER-F1> (enable) set port flowcontrol 2/1-2 receive off Ports 2/1-2 flow control receive administration status set to off (ports will not allow far end to send flowcontrol) 4003-ER-F1> (enable) set port negotiation 2/1-2 enable Ports 2/1-2 negotiation enabled 4003-ER-F1> (enable) set port name 2/1-2 GEC 802.1Q Trunk Ports 2/1-2 name set. 4003-ER-F1> (enable) set port channel 2/1-2 desirable Port(s) 2/1-2 channel mode set to desirable. 4003-ER-F1> (enable) set trunk 2/1 desirable dot1q Port(s) 2/1-2 trunk mode set to desirable. Port(s) 2/1-2 trunk type set to dot1q. 4003-ER-F1> (enable) set module name 3 Gig Server Links Module name set. 4003-ER-F1> (enable) set port name 3/1-2 Corporate Server Ports 3/1-2 name set. 4003-ER-F1> (enable) set port name 3/3 DevEng Server Port 3/3 name set. 4003-ER-F1> (enable) set port name 3/4 QA Server Port 3/4 name set. 4003-ER-F1> (enable) set port flowcontrol 3/1-4 send desired Ports 3/1-4 flow control send administration status set to desired (ports will send flowcontrol to far end if far end supports it) 4003-ER-F1> (enable) set port flowcontrol 3/1-4 receive desired Ports 3/1-4 flow control receive administration status set to desired (ports will allow far end to send flowcontrol if far end supports it) 4003-ER-F1> (enable) set port channel 3/1-2 off Port(s) 3/1-2 channel mode set to off. 4003-ER-F1> (enable) set port channel 3/3-4 off Port(s) 3/3-4 channel mode set to off. 4003-ER-F1> (enable) set trunk 3/1-4 off Port(s) 3/1-4 trunk mode set to off. 4003-ER-F1> (enable) set spantree portfast 3/1-4 enable
Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution.
Enter password: Console> (enable) set system name 5505-WC-F2 System name set. 5505-WC-F2> (enable) set system location 2nd Floor Wiring Closet System location set. 5505-WC-F2> (enable) set system contact sysadmin@bigcorp.com System contact set. 5505-WC-F2> (enable) set time 04/30/1999 10:00:00 Fri Apr 30 1999, 10:00:00 5505-WC-F2> (enable) set password Enter old password: Enter new password: Retype new password: Password changed. 5505-WC-F2> (enable) set enablepass Enter old password: Enter new password: Retype new password: Password changed. 5505-WC-F2> (enable) set banner motd % 5505-WC-F2 (Catalyst 5505) Access Restricted % MOTD banner set 5505-WC-F2> (enable) set interface sc0 10.10.1.30/24 Interface sc0 IP address set. 5505-WC-F2> (enable) set ip route default 10.10.1.1 Route added. 5505-WC-F2> (enable) set ip dns server 10.10.10.100 10.10.10.100 added to DNS server table as primary server. 5505-WC-F2> (enable) set ip dns domain bigcorp.com Default DNS domain name set to bigcorp.com 5505-WC-F2> (enable) set ip dns enable DNS is enabled 5505-WC-F2> (enable) set vtp domain BigCorp mode client VTP domain BigCorp modified 5505-WC-F2> (enable) set module name 1 Supervisor III Module name set. 5505-WC-F2> (enable) set port name 1/1-4 FEC ISL Trunk Ports 1/1-4 name set. 5505-WC-F2> (enable) set port speed 1/1-4 100 Ports 1/1-4 transmission speed set to 100Mbps. 5505-WC-F2> (enable) set port duplex 1/1-4 full Ports 1/1-4 set to full-duplex. 5505-WC-F2> (enable) set port flowcontrol 1/1-4 send off Ports 1/1-4 flow control send administration status set to off (ports will not send flowcontrol to far end) 5505-WC-F2> (enable) set port flowcontrol 1/1-4 receive off Ports 1/1-4 flow control receive administration status set to off (ports will not allow far end to send flowcontrol) 5505-WC-F2> (enable) set port negotiation 1/1-4 enable Ports 1/1-4 negotiation enabled 5505-WC-F2> (enable) set port channel 1/1-4 desirable Port(s) 1/1-4 channel mode set to desirable. 5505-WC-F2> (enable) set trunk 1/1 desirable isl Port(s) 1/1 trunk mode set to desirable. Port(s) 1/1 trunk type set to isl. 5505-WC-F2> (enable) set module name 2 QA 100Mb Hosts Module name set. 5505-WC-F2> (enable) set port name 2/1-4 QA Sparc20 Port 2/1-4 name set. 5505-WC-F2> (enable) set port name 2/5-12 QA NT Workstation Ports 2/5-12 name set. 5505-WC-F2> (enable) set port speed 2/1-12 100 Ports 2/1-12 transmission speed set to 100Mbps. 5505-WC-F2> (enable) set port duplex 2/1-12 full Ports 2/1-12 set to full-duplex. 5505-WC-F2> (enable) set port flowcontrol 2/1-12 send desired Ports 2/1-12 flow control send administration status set to desired (ports will send flowcontrol to far end if far end supports it) 5505-WC-F2> (enable) set port flowcontrol 2/1-12 receive desired Ports 2/1-12 flow control receive administration status set to desired (ports will allow far end to send flowcontrol if far end supports it) 5505-WC-F2> (enable) set port channel 2/1-12 off Port(s) 2/1-12 channel mode set to off. 5505-WC-F2> (enable) set trunk 2/1-12 off Port(s) 2/1-12 trunk mode set to off. 5505-WC-F2> (enable) set spantree portfast 2/1-12 enable
Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution.
5505-WC-F2> (enable) set module name 3 QA 10Mb Hosts Module name set. 5505-WC-F2> (enable) set port name 3/1-48 QA WinNT PC Ports 3/1-48 name set. 5505-WC-F2> (enable) set port duplex 3/1-48 full Ports 3/1-48 set to full-duplex. 5505-WC-F2> (enable) set spantree portfast 3/1-48 enable
Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution.
5505-WC-F2> (enable) set module name 4 Corp/F&A 10Mb Hosts Module name set. 5505-WC-F2> (enable) set port name 4/1-12 Corp Win98 PC Ports 4/1-12 name set. 5505-WC-F2> (enable) set port name 4/13-48 F&A Win98 PC Ports 4/13-48 name set. 5505-WC-F2> (enable) set port duplex 4/1-48 full Ports 4/1-48 set to full-duplex. 5505-WC-F2> (enable) set spantree portfast 4/1-48 enable
Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution.
5505-WC-F2> (enable) set module name 5 S&M 10Mb Hosts Module name set. 5505-WC-F2> (enable) set port name 5/1-48 S&M Win98 PC Ports 5/1-48 name set. 5505-WC-F2> (enable) set port duplex 5/1-48 full Ports 5/1-48 set to full-duplex. 5505-WC-F2> (enable) set spantree portfast 5/1-48 enable
Warning: Spantree port fast start should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc. to a fast start port can cause temporary spanning tree loops. Use with caution.
